Post by Ang on Aug 9, 2005 19:36:12 GMT -5
Essentially, a container candle is a non-flammable container filled with wax and a wick. They have several advantages that make them popular: First of all, they are a bit like a candle and a candle holder rolled into one. They never drip. Also, because they are in a container, we can get away with using lower melting point waxes that enhance scent throw. That fact alone gives scented container candles the ability to effectively throw more scent than their free-standing counterparts.
There are probably as many different ways to make container candles as there are candle makers. What I will do here is present a set of step-by-step instructions that works for me. The wax that I will be using is IGI-4786, a pre-blended container wax that requires no additives.
Step 1) Prepare your molten wax mixture.
You should be able to review these instructions while your wax is melting. Before continuing, set up a double boiler to melt your wax. A good target temperature is 170-175° F (for IGI-4786). Once your wax has completely melted, add any additives you have selected and mix thoroughly. Add them in the following order:
Additives such as vybar or stearic acid (not needed for IGI-4786)
Fragrance Oil
Dye (this is done last so that you get visual confirmation that everything else has mixed well with the wax)
While your wax is melting, proceed through the next few steps. But, monitor your wax temperature carefully during this time.
What you will need: —
Wax suitable for container candles and any desired additives such as dye, fragrance oil, etc.
Containers suitable for candles; many ceramics and glassware fit the bill for this. — Some kind of double-boiler set-up to melt your wax. — Pre-tabbed wicks of a size that is suitable for the diameter of your container. — Hot glue - from a hot glue gun or a hot glue pot — Bic Pen — Clothespins — Thermometer - always use a thermometer when melting wax.
Step 2)
Disassemble a Bic pen. What you are after is the barrel (white). Discard the rest. Straighten your pre-tabbed wicks out. They don't need to be perfectly straight. Insert a pre-tabbed wick through the barrel of the pen barrel. 6" wicks are good for this. If you have a different length, you may have to improvise. The point of the barrel is that it makes handling the wick much easier. While holding the wick within the barrel, apply hot-glue to the base of the wick tab. Using the barrel to guide the wick, press the tab to the center of your container. Slide the barrel off the wick.
Proceed to the next step.
Step 3) Secure the top of your wick.
Using a clothespin, secure the top of your wick. Clothespins work for containers with a opening diameter of up to three inches. For larger containers, you will have to improvise. Looping the wick around a wooden skewer also works. The objective here is to provide some sort of support to help keep the wick centered while the wax is cooling. You can actually carryout this step after you have poured your wax.
Step 4) Pre-heat your container.
Once your wax mixture is at the proper temperature, and you have thoroughly mixed in any additives, pre-heat your container to about 150 degrees F. Pre-heating can be done in the oven on the lowest heat setting. If you are using a heat gun, exercise some care as heat guns can get much hotter than 150 degrees F.
Step 5) Initial Pour.
With your wax at the proper temperature (160 degrees F), carefully fill your container to the desired level. If it is a container with a lid, remember to fill it only to a level that will leave enough room for the lid to properly fit back on the finished candle. Save about 20% of the wax in the pouring pitcher for Step 6. Do NOT return it to the heat source. Allow the wax to completely cool before proceeding. This will typically be six or more hours. Slow cooling generally provides the best results when it comes to container candles. So, don't attempt to accelerate the cooling process.
Step 6) Re-pour
Once your candle has completely cooled, you will notice that the wax has sunken a bit in the middle. With the wax that you saved from the previous step, melt it back down and bring it to a temperature of 185 degrees F. We use a higher temperature for the second pour because it increases the adhesion between layers of wax.
Re-pour to a level that just barely covers the wax from the initial pour. Going to this level helps hide any seam lines. Allow your candle to completely cool.
Once your candle has completely cooled, remove the clothespin and trim the wick to ¼"
There are probably as many different ways to make container candles as there are candle makers. What I will do here is present a set of step-by-step instructions that works for me. The wax that I will be using is IGI-4786, a pre-blended container wax that requires no additives.
Step 1) Prepare your molten wax mixture.
You should be able to review these instructions while your wax is melting. Before continuing, set up a double boiler to melt your wax. A good target temperature is 170-175° F (for IGI-4786). Once your wax has completely melted, add any additives you have selected and mix thoroughly. Add them in the following order:
Additives such as vybar or stearic acid (not needed for IGI-4786)
Fragrance Oil
Dye (this is done last so that you get visual confirmation that everything else has mixed well with the wax)
While your wax is melting, proceed through the next few steps. But, monitor your wax temperature carefully during this time.
What you will need: —
Wax suitable for container candles and any desired additives such as dye, fragrance oil, etc.
Containers suitable for candles; many ceramics and glassware fit the bill for this. — Some kind of double-boiler set-up to melt your wax. — Pre-tabbed wicks of a size that is suitable for the diameter of your container. — Hot glue - from a hot glue gun or a hot glue pot — Bic Pen — Clothespins — Thermometer - always use a thermometer when melting wax.
Step 2)
Disassemble a Bic pen. What you are after is the barrel (white). Discard the rest. Straighten your pre-tabbed wicks out. They don't need to be perfectly straight. Insert a pre-tabbed wick through the barrel of the pen barrel. 6" wicks are good for this. If you have a different length, you may have to improvise. The point of the barrel is that it makes handling the wick much easier. While holding the wick within the barrel, apply hot-glue to the base of the wick tab. Using the barrel to guide the wick, press the tab to the center of your container. Slide the barrel off the wick.
Proceed to the next step.
Step 3) Secure the top of your wick.
Using a clothespin, secure the top of your wick. Clothespins work for containers with a opening diameter of up to three inches. For larger containers, you will have to improvise. Looping the wick around a wooden skewer also works. The objective here is to provide some sort of support to help keep the wick centered while the wax is cooling. You can actually carryout this step after you have poured your wax.
Step 4) Pre-heat your container.
Once your wax mixture is at the proper temperature, and you have thoroughly mixed in any additives, pre-heat your container to about 150 degrees F. Pre-heating can be done in the oven on the lowest heat setting. If you are using a heat gun, exercise some care as heat guns can get much hotter than 150 degrees F.
Step 5) Initial Pour.
With your wax at the proper temperature (160 degrees F), carefully fill your container to the desired level. If it is a container with a lid, remember to fill it only to a level that will leave enough room for the lid to properly fit back on the finished candle. Save about 20% of the wax in the pouring pitcher for Step 6. Do NOT return it to the heat source. Allow the wax to completely cool before proceeding. This will typically be six or more hours. Slow cooling generally provides the best results when it comes to container candles. So, don't attempt to accelerate the cooling process.
Step 6) Re-pour
Once your candle has completely cooled, you will notice that the wax has sunken a bit in the middle. With the wax that you saved from the previous step, melt it back down and bring it to a temperature of 185 degrees F. We use a higher temperature for the second pour because it increases the adhesion between layers of wax.
Re-pour to a level that just barely covers the wax from the initial pour. Going to this level helps hide any seam lines. Allow your candle to completely cool.
Once your candle has completely cooled, remove the clothespin and trim the wick to ¼"